UniFi U7 Pro XG Wall Table Stand

Put your UniFi U7 Pro XG Wall on a desk, shelf or benchtop — no drilling, no bracket, no patching holes later. The UACC-U7-Pro-XG-Wall-TS is Ubiquiti's official table stand for the U7 Pro XG Wall, holding the AP upright at its intended angle on a weighted, non-slip base. Ideal for site surveys, demos, pop-up sites, rentals and anywhere permanent mounting isn't an option.

Key features

• Purpose-built for the U7 Pro XG Wall — an official Ubiquiti accessory machined around this specific AP chassis, so the unit seats flush and secure with no adapters or third-party brackets.
• No drilling, no wall damage — turn any desk, shelf, credenza or comms-room bench into a mounting point. Perfect for leased offices, heritage buildings and fit-outs where you can't touch the walls.
• Stable, weighted base — an aluminium alloy and polycarbonate build weighing 200 g keeps the AP planted, while silicone rubber contact points resist sliding and protect furniture surfaces.
• Keeps the AP correctly oriented — the U7 Pro XG Wall is engineered to radiate outward from a vertical surface. The stand preserves that orientation, so you get the coverage pattern the AP was designed for.
• Genuinely portable — at 200 g and 181.9 × 83.8 × 77.5 mm it packs into a site-survey kit, demo case or go-bag alongside a PoE injector.
• Neutral UniFi aesthetic — the same clean, low-profile design language as the rest of the UniFi range, so it looks at home in a boardroom or reception area.

Wall-mount performance without the wall

The UniFi U7 Pro XG Wall is one of Ubiquiti's best-performing WiFi 7 access points — tri-band, six spatial streams, 300+ clients, and a 10 GbE PoE+ uplink that removes the wired bottleneck entirely. But it's designed to be fixed to a vertical surface. That's a problem when you're testing coverage, running a temporary event network, fitting out a leased tenancy, or simply can't put fixings into the wall.

The U7 Pro XG Wall Table Stand solves it. It holds the access point upright on any flat surface, at the orientation it was engineered for, with a weighted base that keeps it there. Drop it on a desk, plug in the PoE uplink, and you have a fully functional AP in seconds.

Built to Ubiquiti's standard

The stand combines three materials for a reason. Polycarbonate forms the main body — light, tough and colour-matched to the UniFi range. Aluminium alloy adds mass low in the structure, so the centre of gravity stays down and the AP doesn't tip when a cable is tugged. Silicone rubber handles the contact surfaces, gripping the desk and protecting timber, glass and laminate from scuffing.

The whole assembly weighs 200 g and measures 181.9 × 83.8 × 77.5 mm (7.2 × 3.3 × 3.1"), giving it a footprint small enough for a crowded desk.

Where it earns its place

• Site surveys and validation — position a real U7 Pro XG Wall exactly where the design calls for it, take readings, then move it. No temporary fixings, no drywall repairs.
• Demos and sales engineering — show a client genuine multi-gigabit WiFi 7 throughput on their own desk rather than a spec sheet.
• Temporary and event networks — pop-up retail, trade stands, conference rooms, construction site offices and training rooms.
• Leased and heritage premises — deliver enterprise WiFi where the lease or the building fabric forbids drilling.
• Small offices and home offices — a single AP on a shelf covers a floor without a cabling contractor.
• Spares and staging — keep an AP live and reachable on the bench while you configure, update or troubleshoot it.

Installation

Seat the access point into the stand, route the Ethernet cable out of the rear, and connect to a PoE+ source. The U7 Pro XG Wall draws both power and data over its single 10 GbE PoE+ port, so one cable is all you need. Full instructions are in Ubiquiti's installation guide for the UACC-U7-Pro-XG-Wall-TS.