Set up and use a UniFi Cloud Gateway Industrial

The Cloud Gateway Industrial is a fanless UniFi gateway built for sites where dust, vibration and temperature swings are part of daily life. [1] It puts a gateway, WiFi 7, 270W of PoE and the full set of UniFi apps into one metal box. [2] This guide covers where it can go, how to mount and power it, and how to plan its ports, antennas and storage for a shed, plant room, workshop or farm building.

Outcome and equipment

By the end, your gateway will be mounted somewhere it can cope with and running from the right power supply, with its PoE budget worked out and its WiFi, storage and backup internet planned.

  • A Cloud Gateway Industrial and its power adapter.
  • A thermometer that records the highest temperature, so you can check the spot before you mount anything.
  • Fixings for the wall, or the optional rack kit.
  • Network cables, plus an SFP+ module or DAC cable if you're using the SFP+ port.
  • The UniFi app, or a computer with a browser.
  • Your ISP's settings, from Connect UniFi to nbn in Australia.
  • A network feed to the building, if the nbn doesn't arrive there. Extend UniFi connectivity to a garage or shed compares your options.

Know what it's built for

Feature Cloud Gateway Industrial [2]
Default WAN ports 10G SFP+, 10 GbE RJ45 and 2.5 GbE RJ45
Default LAN ports 3 × 2.5 GbE [2]
Rated IPS 5 Gbps
Most WANs 5
PoE 5 ports, 270W in total
WiFi WiFi 7 on 2.4 and 5 GHz, 2×2, rated for 115 m²
Storage microSD, 128 GB included
Cameras 15 HD, 8 2K or 5 4K
Access hubs 50
Rated for 50+ devices, 500+ users
Working temperature −30 to 50 °C
Humidity 5 to 95%, non-condensing
Size and weight 307.9 × 203.5 × 43.7 mm, 2.4 kg

Two points are easy to miss. First, tough doesn't mean weatherproof. Ubiquiti says it's built for dusty sites, but neither its launch post nor its spec sheet gives an IP rating. [1] [2] Treat it as an indoor device for a rough room. Keep it out of the rain, direct sun and any wash-down area.

Second, the WiFi is a convenience rather than the main attraction. It's 2×2 dual-band, with no 6 GHz radio. [2] If WiFi is your main need, a separate access point will do better, and this gateway has plenty of PoE to run one.

Check the heat first

The 50 °C limit is 10 °C higher than the rating on the rack-mounted Dream Machines, but a metal shed in full sun can still go past it. [2] [3] The limit applies to the air around the gateway, not to the forecast. An outdoor reading of 38 °C can mean something much hotter under an uninsulated roof.

  1. Measure the spot. Leave a thermometer there through a few hot days and note the peak. If you can't measure in summer, assume the room will run well above the outdoor temperature.
  2. Mount it low and in shade. Hot air collects under the roof. A low position on an inside or south-facing wall stays cooler than the top of a west-facing steel wall.
  3. Leave air around it. It's fanless, so it relies on air moving past its case. [1] Don't box it in or stack other equipment against it.
  4. Take care with cabinets. A sealed box keeps out dust but traps heat, and a steel one blocks WiFi. Measure the temperature inside the cabinet, not outside it. If it runs hot, use a vented cabinet with filters, and move the WiFi to an access point outside.
  5. Avoid condensation. The humidity rating is non-condensing. [2] Keep the gateway away from roller doors, hoses and anywhere that gets damp when the temperature falls overnight.

The rating is for the gateway, so keep the power adapter somewhere dry and shaded too. If you fit an SFP+ module, check its temperature rating, because it may not match the gateway's.

Mount it

It can sit flat or upright on a bench, go under a desk, mount on a wall or fit into a 19" rack. You can switch between desktop and rack without tools, but a wall mount still needs screws. [1]

  • Wall: this is usually the best choice in a shed, because it keeps the gateway off the bench and away from knocks and dust. Fix into a stud or masonry. It's 2.4 kg, plus the weight of its cables. [2]
  • Rack: the UACC-UCG-Industrial-RM kit is 1U, and the gateway's two handles slide out to fit it. [1] [4] It includes a tray for the power supply. [1]
  • Bench: fine for a clean office. On a workbench, it's likely to collect swarf, dust and the odd dropped tool.

Leave room around the cables and antennas, and make sure you can reach the ports and the reset button later.

Power it

Your power choice sets how much PoE you get, and the difference is large. [2]

Power source PoE budget
DC jack, with the 350W adapter 270W
4-pin 48V DC input 75W

The 48V input suits a site that already has a DC supply, but plan on 75W for your PoE devices. [1] [2] New mains wiring in a shed must be done by a licensed electrician. DIY electrical work is illegal, and the rules vary slightly by state. [5] On rural sites, it's also worth using a surge-protected board or a UPS, because lightning and rough power are common out there. If you add a UPS, size it for the gateway and all of its PoE devices together. Our UniFi power products are a good place to start.

Plan the ports and PoE

Here's how Ubiquiti lists the ports and their PoE. [2]

Port Speeds PoE
2 × 2.5 GbE RJ45 2.5 or 1 Gbps, or 100 Mbps PoE+++, up to 90W each
2 × 2.5 GbE RJ45 2.5 or 1 Gbps, or 100 Mbps PoE+, up to 30W each
1 × 10 GbE RJ45 10, 5, 2.5 or 1 Gbps, or 100 Mbps PoE+++, up to 90W
1 × SFP+ 10 or 1 Gbps None

The 10 GbE RJ45 port is both a default WAN and a PoE+++ port, and one of the 2.5 GbE ports is a WAN by default too. [2] Ubiquiti promotes direct power for LEO satellite terminals, so a WAN port may still supply PoE. [1] Before you plug in a high-power device, read the port labels on your unit, then check each port's role and PoE setting in UniFi Network.

Add up your power

Add the maximum draw of each device and leave some spare. As an example, one 60W device, two 25W access points and two 13W cameras come to 136W. That's fine on the 270W budget, but almost double the 75W budget on the 48V input. Choose a UniFi PoE switch or injector shows the sums in more detail, and what to do if you run out.

Copper cable between buildings is best avoided, because different earth points and lightning can damage equipment at both ends. Use fibre or a wireless bridge instead, as covered in Extend UniFi connectivity to a garage or shed. In Australia, fixed customer cabling must be installed by a registered cabler, or someone they directly supervise. Fibre, underground and aerial runs each need the matching competency, and an electrical licence alone doesn't cover this. [6]

First-time setup

  1. Connect the WAN. Plug the nbn box or modem into a WAN port. The 2.5 GbE port suits most nbn plans. [2] nbn FTTP still connects by Ethernet from the nbn box, so keep the SFP+ port for your own fibre link from another building. FTTN and FTTB services need a VDSL2 modem in front of the gateway. [7] [8]
  2. Power it on. Fit the antennas first, then connect the power.
  3. Set it up. In the UniFi app, follow the setup wizard, and stay within 3 m if you're connecting over Bluetooth. [9] Or connect a computer to a LAN port and browse to unifi/. [9]
  4. Enter any ISP details. If your ISP uses PPPoE, enter it at Settings › Internet. [10]
  5. Update. Go to Settings › Control Plane › Updates. [11]
  6. Turn on backups. Tick System Backups at Settings › Control Plane › Backups. [12]
  7. Secure it. A remote site is a poor place for a default setup, and nobody's there to notice a problem. Follow Secure a UniFi Cloud Gateway from day one.

Choose your antennas and plan the WiFi

Ubiquiti lists two antenna types for this model, and the spec sheet doesn't say when to use each. [2]

Antenna 5 GHz gain 2.4 GHz gain
Stub 5 dBi 3 dBi
Terminal omni 6 dBi 6 dBi

The gains are close, so where the gateway sits matters more than which antenna you fit. Try the options you have, and walk the room with a phone before you settle on one.

Ubiquiti rates coverage at 115 m² and doesn't state the conditions. [2] Steel walls, racking and machinery will cut that figure quickly. The built-in WiFi suits an office or workshop near the gateway. For the rest of a large shed, or the yard outside, add an access point. Choose UniFi access point locations shows how to test each spot.

Plan cameras and storage

The gateway can handle up to 5 4K cameras, but its storage is the tighter limit. [2] It records to microSD, and the spec sheet lists no other storage. [2] At 4 Mbps of continuous recording, the 128 GB card holds about three days of footage from one camera, and less than a day from four.

  • Record on motion or smart detections, which stretches the card a long way.
  • Use an endurance card. Ubiquiti's own cards are made for constant writing, and go up to 1 TB. [13] Check that the size you choose works in this model before you order.
  • Add a dedicated recorder if you want weeks of footage. See Run UniFi Protect and Access on a Cloud Gateway.

Plan backup internet

Rural sites often need a second link, and this gateway takes up to five WANs. [2]

  • Second connection: connect Starlink, 5G or another service to a spare port, and assign it the WAN role at Settings › Internet. [10] Ubiquiti says the gateway can power LEO satellite terminals directly, so check what your terminal needs before you add a separate power supply. [1] Backup internet for Australia compares your options, and Configure UniFi backup internet and failover shows the setup.
  • WiFi Uplink: Ubiquiti lists this for the Industrial, so it can use another WiFi network as a backup. It needs Network 11 and UniFi OS 6.0.10 or newer, so check the version on your gateway first. [14]
  • SIM slots: there's no built-in modem. The two SIM slots are for Remote SIM with the separate UniFi 5G Max Outdoor, and that feature was still waiting on a software update when we wrote this. [15] [16] Don't buy the gateway for its SIM slots until you've confirmed it works.

Starlink and mobile services often don't give you a public IP address, and port forwarding needs one, so port forwards may not work over them. [17] [18] Use Teleport to reach the site remotely, because it works when the gateway is behind NAT. [19]

Verification

  • A wired speed test is close to your plan speed.
  • Each port shows the role and link speed you expect.
  • Every PoE device stays up with everything running at once.
  • WiFi reaches the places you need, with machinery and doors in their working positions.
  • If you use a camera, Protect records and plays back a test clip.
  • Check the peak temperature at the gateway's spot after a hot day, and confirm it's under 50 °C.
  • Unplug your main WAN and confirm the backup takes over, then plug it back in.
  • Restart the gateway, and confirm the internet, WiFi and PoE devices all return by themselves.
  • Confirm that you can reach the gateway remotely from a phone on mobile data.

Troubleshooting and recovery

Problem Likely cause What to do
PoE devices drop out or won't start Over budget, especially on the 48V input [2] Add up the draw, move to the DC adapter, or add a PoE switch.
A device needing 60W won't start It's on a PoE+ port, which gives 30W [2] Move it to a PoE+++ port.
A PoE port gives no power Its PoE is turned off, or the device needs more than the port supplies Check the PoE setting in UniFi Network, and the device's power needs.
Restarts or dropouts on hot days Air around the gateway is above its rating [2] Move it lower, shade it, or improve the ventilation.
Weak WiFi around the shed Metal walls, racking or a metal cabinet Add an access point, and test again.
Recording stops or has gaps The microSD card is full or worn out Fit an endurance card, or add a recorder.
Link between buildings keeps failing Copper run, poor termination or a surge Move to fibre or a wireless bridge.
SIM slots do nothing They need the UniFi 5G Max Outdoor and a software update [16] Use a separate 5G router or modem for now.

If the gateway won't respond, see Update, recover and replace a UniFi Cloud Gateway.

Sources:

Back to the series

Leave a comment

Please note, comments need to be approved before they are published.